Some Help would be appreciated. I am on Altis, setting up an Asymmetric insurgency. I have dived the map in half with two markers, and have an Opcom in Asymmetric mode synced to, two sets of civ and mil placement modules one with the TAOR set to the east marker and one set with the west marker, so both halves of the map are covered, they are set to objectives only, i have hand placed some units down for the opcom to start with. However it seems to be insistent on sending all units it can to objectives near the Pyrgos area, where as the player forces deploy from the AAC airfield. Is there a way to make it so that the units in the east half only operate on objectives in the east marker, and the western units only operate in their western marker? I tried setting up two opcoms one for each half but you can only have one opcom assigend to a single faction. Any help would be greatly appreciated.

Also some insight into how the AI recognize and behave when players enter and hold an objective they are aware of would be helpful. E.G: If using the player logistics i set up a FOB in the town of Athira which the opcom new about, would they recognize that as a player base and try to assault/raid it if they felt they had the force strength to do so?

Thanks that is certainly going to help with the FOB aspect, just now need an answer to the first part, though i am starting to think it isn't possible to make what i am looking for.

Didn't think so, as far as i can tell asymmetric is designed to slowly spread out, though i am unsure if they will spread further than there initial marker. E.G if they start with placements inside a 3000x3000 marker, will they eventually start occupying things 6000 meters away?

@SpyderBlack723 If you have control of the area then it would see that as a hostile zone and act accordingly. If you want to make an FOB in an area that won't have an objective then you can use this little script.

setFOB.sqf :

_caller = _this select 1;

cjb_addObjectiveToSides = {
	private["_objectiveParams","_factions","_faction","_opcom","_opcomSide"];
	_objectiveParams = _this select 0;
	_factions = _this select 1;
	{
		_opcom = _x;
		{
			_faction = _x;
			_opcomSide = [_opcom,"side",""] call ALiVE_fnc_HashGet;
 
			if( _opcomSide == _faction) then {
				[_opcom, "addObjective", _objectiveParams] call ALiVE_fnc_OPCOM;
			};
		} forEach _factions;
	} forEach OPCOM_INSTANCES;
};

_n = format["%1_obj", floor (random 1000)];
[[_n, getPos _caller, 100,"MIL"],["WEST","EAST"]] call cjb_addObjectiveToSides;
hint "FOB has been set";

and then simply add an action to a unit to use the script:

this addAction ["Set FOB","setFOB.sqf"];

This will create an objective at the location of the person using the "Set FOB" action and then register to OPCOM sides East and West (Can be changed according to your needs).

.. I haven't messed around with it yet but you could do some interesting stuff with this aswell, like setting up a trigger on an FOB you created and then when hostile units are within that trigger, the base is registered as an objective to the enemy opcom.

With the 0.9.8 i'm not sure if this is working properly now the AI don't seem to be recognizing it as an enemy position they had orders to fallback to an FOB i set up, and to setup a depot there, is there a way to force it to be a bluefor objective when it is initially spawned, or at least to a debug to show what side holds it, as far as i'm aware in Asym mode debug it shows the hostility levels of that objective, which are also spawning at 10 on FOB's i create. :/

Will do some more testing of this now tomorrow then, thanks for the reply. :)